Heinrichs Electromagnetic Flowmeters
Magnetic Inductive Flow Meter
Model: EPS
Applications
Volume flow measurement of electrically conductive liquids, slurries and pastes without loss of pressure
Special features
- High accuracy
- No maintenance required
- No pressure drop
- Wide spectrum of electrode materials
- Many liners available
- Inexpensive grounding electrode available instead of grounding rings, also available special materials like e. g. tantalum
- Large selection of process connections
Technical data
Sensor EPS
- Body: Coated steel
- Process connection: Steel or stainless steel 1.4301 flanges (EN1092, ASME B16.5 and JIS) Food connection DIN11851, TriClamp® , (others on request)
- Lining: Hard rubber, Soft rubber, PTFE, EPDM and Ceramic
- Measuring and grounding electrodes: Stainless steel 1.4571, Hastelloy C276, Tantalum, Platinum (Grounding ring and other materials on request)
- Nominal diameters: DN15 up to DN 1200 (others on request) 2 / 3 / 6 / 10mm inner diameter with process connection G1/2” (m) or ½” NPT(m)
- Nominal pressure: PN40/ASME Class 300 for DN15 to DN300
PN16, ASME Class 150 for DN50 to DN600
PN10, ASME Class 150 for DN200 to DN1200
- Process temperature:
- -10°C up to +70°C EPDM
- 0°C up to +95°C Hard rubber (Ebonite)
- 0°C up to +70°C Soft Rubber
- -20°C up to +150°C PTFE and Ceramic
- Ambient temperature: -20 °C to +60 °C, depending on process temperature
- Conductivity: >5µS/cm ,>20 µS/cm for demineralized water
- Range limits: 0,5 m/s – 10 m/s
- Accuracy: ± 0.3 % of measured value ± 0.01 % * (Q at 10 m/s) (under reference conditions)
- Repeatability: ± 0.15 % of measured value ± 0.005 % * (Q at 10 m/s) (under reference conditions)
- Ingress protection: Standard IP 67 (EN60529), IP68 on request
Transmitter UMF2
- Installation: integral or remote
- Housing: Aluminum die cast, coated
- Power supply: 115 / 230 VAC 50/60Hz 10VA, 24 VDC 10W
Outputs:
- Analog: 1 x 0/4-20 mA active, galvanically isolated
- Pulse: passive, galvanically isolated, 24V, 60mA
- Status: passive, galvanically isolated, 24V, 60mA
- Ambient temperature: -20 °C to +60 °C, depending on process temperature (integral installation)
- Ingress protection: IP67 (EN60529), IP68 on request
- Diagnostic Functions: Empty pipe detection, exciter current monitoring
- Electromagnetic compatibility: EMC Directive 2014/30/EU (EMC)
- Low Voltage directive: 2014/35/EU (LVD)
Communication
4-20mA, HART® Protocol
Magnetic Inductive Flow Meter ATEX
Model: EPX
Magnetic-Inductive flowmeter
for hazardous areas
Applications
Volume flow measurement of electrically conductive liquids in hazardous areas without pressure loss.
Special features
- ATEX approval
- High accuracy
- No maintenance required
- No pressure drop
- Wide spectrum of electrode materials
- Many liners available
- Inexpensive grounding electrode available instead of grounding rings, also available special materials like e. g. tantalum
- Large selection of process connections
Technical data
Sensor EPX
- Body: carbon steel painted Ex IIG or st.st. Ex IID
- Process connections: carbon steel or st.st. flanges (1.4301 / SS316) EN1092 und ASME
- Lining: hard rubber, soft rubber, E-CTFE, PTFE,
- Measuring and grounding electrodes: st.st. 1.4571, hastelloy, tantalum, platinum (Grounding ringa and other materials on request)
- Nominal diameters: DN15 (1/ 2 inch) up to DN 300 (12 inch)
Nominal pressure
- PN40, ASME Cl150/300 DN15 (1/2 inch) up to DN50 (2 inch)
PN16, ASME Cl150 DN65 (2 ½ inch) uzp to DN200 (8 inch)
PN10, ASME Cl150 DN250 (10 inch) bis 300 (12 inch) (higher on request) - Process temperature:
Hard rubber -35….+64°C(T6)
Soft rubber +5…..+64°C (T6)
PTFE -35…+64°C (T6) ..+79°C(T5) ..+114°C(T4) ..+139°C(T3) - Ambient temperature: -35°C …. +60°C
- Conductivity: >5 µS/cm
>20 µS/cm for demineralized water - Range limits: 0,1 m/s – 10 m/s
- Accuracy: ±0,3% of actual ±0,01% (Q at 10m/s) (under reference conditions)
- Repeatability: ±0,15% of actual ±0,005% (Q at 10m/s) (under reference conditions)
- Ingress protection: IP67 (EN60529), IP68 on request
Transmitter
UMF3
- Installation: integral or remote
- Housing: aluminum die cast, coated
- Power supply : 90…253V AC 50/60Hz, 24V DC ±20%
Outputs
- Analogue: 1x 0/4-20mA HART, passive, galvanically seperated
- Pulse output: passive, galvanically seperate, Um=30VDC
- Status output: passive, galvanically seperate, Um=30V,
- Ambient temperature: -20°C …. +60°C
- Ingress protection: IP67
- Diagnosis function: empty pipe detection, coil current monitoring
Hazardous Area Protection
Ex II(1G) 2G Ex d e [ia Ga] IIB T6/T4/T3 Gb
Ex II(1G) 2D Ex tb IIIC [ia Ga] T80 °C / T125 °C / T 150 °C Db
Communication
HART® protocol
Magnetic Inductive Flow Meter
Model: EP
Applications
Volume flow measurement of electrically conductive liquids, slurries and pastes without loss of pressure.
Special features
- High accuracy
- No maintenance required
- No pressure drop
- Wide spectrum of electrode materials
- Many liners available
- Inexpensive grounding electrode available instead of grounding rings, also available special materials like e. g. tantalum
- Large selection of process connections
Technical data
Sensor EP
Body: Coated steel
Process connection: Steel or stainless steel 1.4301 flanges (EN1092 und ASME B16.5),
Flangeless connection (wafer), food connection DIN11851,
TriClamp® , (others on request)
Lining:Hard rubber, soft rubber, PTFE, Rilsan (in preparation),
PFA (in preparation),Wagunit
Measuring and grounding electrodes: Stainless steel 1.4571, Hastelloy C4, Tantalum on request, Platinum;
Grounding ring and other materials on request
- Nominal diameters: DN15 bis DN 300 (others on request)
Nominal pressure:
- PN 40, ASME Cl150 / 300 DN15 to DN50
- PN 16, ASME Cl150 DN50 to DN200
- PN 10, ASME Cl150 DN250 to DN300(higher pressure rates on request)
Process temperature:
0 °C to +80 °C (hard rubber, soft rubber, PFA)
-20 °C to +150 °C (PTFE)
0 °C to +80 °C(Rilsan, Wagunit)
Ambient temperature: -20 °C to +60 °C, depending on process temperature
Conductivity: >5µS/cm ,>20 µS/cm for demineralized water
Range limits: 0,5 m/s – 10 m/s
Accuracy: ± 0.3 % of measured value ± 0.01 % *
(Q at 10 m/s) (under reference conditions)
Repeatability: ± 0.15 % of measured value ± 0.005 % *
(Q at 10 m/s) (under reference conditions)
Ingress protection: IP 67 (EN60529), IP68 on request
Transmitter UMF2
Installation: integral or remote
Housing: Aluminum die cast, coated
Power supply: 115 / 230 VAC 50/60Hz 10VA, 24 VDC 10W
Outputs:
Analog: 1 x 0/4-20 mA active, galvanically isolated
Pulse: passive, galvanically isolated, 24V, 60mA
Status: passive, galvanically isolated, 24V, 60mA
Ambient temperature:-20 °C to +60 °C, depending on process temperature (integral installation)
Ingress protection: IP67 (EN60529) Diagnostic Functions: Empty pipe detection, exciter current monitoring
Electromagnetic compatibility: EMC Directive 89/336/EWG
Communication
4-20mA, HART® Protocol
Magnetic Inductive Flow Meter
Model: PIT
Electromagnetic Insertion Sensor
Applications
Volume flow measurement and monitoring of electrically conductive liquids, slurries and pastes.
Suitable for fluids which tend to fat films or crusts.
Special features
- Low cost alternative to traditional in-line devices
- Suitable for pipe diameters up to DN 2000
- Under operating conditions mountable or dismountable,
- Used in hazardous areas
Technical data
Sensor
Materials:
Body: Stainless steel / PTFE, PFA (others on request).
Electrodes: Hastelloy, Tantalum, Platinum, (others on request)
End connections: flanges acc. EN 1092, ASME B16.5, DIN2512, (others on request)
Nominal pressure: PN 16, ASME Cl150 / 300 (stainless steel / PTFE) PN 40, ASME Cl150 / 300 (PFA) (others on request)
Process temperature: -40°C up to +100°C (stainless steel / PTFE) -40°C up to +150°C (PFA)
Ambient temperature: -40°C up to +60°C
Ingress protection: IP 65 / IP 68 (EN60529)
Range of application
For sizes: DN125 up to DN2000 (stainless steel / PTFE)
DN125 up to DN600 (PFA)
Range limits standard: 1 m/s – 10 m/s , Special: 0,5 m/s – 5 m/s
Transmitter
UMF – UMF2
Installation: integral or remote
Power supply: 115 / 250 VAC (UMF, UMF2)
24 VDC (UMF, UMF2)
24 VAC (UMF)
Outputs: galvanically isolated
Analog: 2 x 0/4-20 mA (UMF)
1 x 0/4-20 mA (UMF2)
Binary 1: active, potential free 24 V=, max. 200 mA (UMF)
passive, optocoupler, (UMF, UMF2)
Ui=30 V, Ii=200mA, Pi=3 W
Binary 2 (status): passive, optocoupler, (UMF)
Ui=30 V, Ii=200mA, Pi=3 W
Binary 3 (optional): passive, optocoupler, (UMF)
Ui=30 V, Ii=200mA, Pi=3 W
Ambient temperature: -20°C up to +60°C
Ingress protection: IP 68 (EN60529)
Accuracy: ± 1,5% of reading ± 0,5% from upper range value
Approvals and certificates
Explosion protection:
Sensor: BVS 03 ATEX E 150 X
II 2G EEx e[ia] IIC T3-T6
NEPSI Approval Cert. No. GYJ06474X
Transmitter: DMT 99 ATEX E 107 (UMF)
Increased safety EEx e (connection): II (1)2G EEx de[ia] IIB/IIC T3-T6
Explosion proof:EEx d(connection II (1)2G EEx d[ia] IIB/IIC T3-T6
Signal out- inputs: intrinsically safe / not intrinsically safe
NEPSI Approval Cert No. GYJ06475
CE-Mark: Explosion Protection Directive 94/9/EC
EMC-Directive 89/336/EEC
Communication
4-20 mA, HART® protocol (UMF, UMF2)
Magnetic Inductive Insertion Flow Sensor
Model: PITe
Applications
Volume Flow measurement and monitoring of electrically conductive liquids. ECONOMIC sensor version for larger pipe sizes up to DN 400 / 16 inch.
Special features
- ECONOMIC version with weld-on adapter
- Low cost alternative for classic in-line meters
- Suitable for pipe diameter up to DN 400 / 16 inch
- Sensor installation and removal with threaded quick release
Technical data
Materials
- Sensor body: st.st. / sensor tip PTFE
- Electrodes: st.st. / hastelloy
- Process connection: weld-on adapter with cap nut sensor fixing
- Nominal pressure: PN16
- Pipe sizes: DN 80/3“ ….. DN 400/16“
- Process temperature: -20°C …. +100°C
- Ambient temperature: -20°C ….. +60°C
- Ingress protection: IP65 / IP68
- Range limitations: 1 m/s…..10 m/s
Transmitter
UMF2 – remote mounting
Power supply: 115 / 250VAC / 24 VDC
Output signal galvanically separated )
- 1x 0/4-20mA, HART
- 1x status output, passive
- 1x pulse output, passive
- Ambient temperature: -40°C …. +60°C
- Ingress protection : IP 65 / IP68 (EN60529)
- Accuracy:
at (Q≥30% of URV): ± 1,5% of actual
at (Q≤30% of URV): ± 1,5% of actual ± 2,5% URV
(under reference conditions) - Repeatability: ± 0,75%
(under reference conditions)
Approvals and certificates
CE- marking,
EMC guide line 2014/30/EU
Communication
HART® protocol
Magnetic Inductive Flow Meter
Model: MIK
Application
Volume flow measurement of electrically conductive liquids, acids and caustic liquids. without pressure loss
- Drinking, cooling and waste water
- Ground water, tap water
- Machine building
- Chemical industry / laboratory use
- Automotive
Special Features
- Compact OEM version
- Wear free
- without pressure loss
- Sensor body made from PPS or PVDF
- Large selection on electrode meterials
- Large selection of process connections
Technical data
- Sensor body: PPS c/w sxt.st. electrodes ; PVDF c/w hastelloy- oder tantalum-electrodes, sealing NBR, FPM, FFKM
- Process connections: G ½ AG …G 2 ¾ AG
- Connection sets: PVC – glue connection or hose connection, weld-on set st.st.
- Lining free version as sensor body base material is PPS or PVDF
- Measuring electrodes: st.st. 1.4401, Hastelloy C4, Tantalum,
- Max. pressure: 10 bar
- Process temperature: -10°C up to +80°C ( max. 60°C for PVC connections )
- Ambient temperature: -10°C up to +60°C
- Conductivity: >30 µS/cm
- Max. media viscosity: 20 cSt ≤ G1“ ; 70 cSt ≥G 1 ½“
- Flow Ranges: 0,01-0,5 ….35-700 l/min
- Meas. Accuracy: ±2% FS
- Repeatability: ±1% FS
- Response time: ~ 1s
- Protection: IP65
Elektronic versions
› FREQUENCY OUTPUT
- F300 M12 Plug, 500 Hz
- F390 M12 Plug, 50…1000 Hz
› SWITCHIN OUTPUT
- S300 M12 plug, relay output
- S30D M12 plug. active 24 VDC
› ANALOG OUTPUT
- L303 M12 plug, 0-20 mA
- L343 M12 plug, 4-20 mA
- L443 DIN plug, 4-20 mA
› COMPACT ELECTRONICS
- C30R M12 plug, 2x open coll. PNP
- C30M M12 plug, 2x open coll. NPN
- C34P M12 plug, 0(4)-20 mA, 1x open coll. PNP
- C34N M12 plug, 0(4)-20 mA, 1x open coll. NPN
› COUNTER ELECTRONICS
- E14R 1m cable, LCD, 0(4)-20 mA, 2x Relay,
- E34R M12 plug, LCD, 0(4)-20 mA, 2x Relay,
- E94R M12 plug + 1m cable, LCD, 0(4)-20 mA, 2x relay,
› DOSING ELECTRONCIS
- G14R 1m cable, LCD, 0(4)-20 mA, 2x relay
- G34R M12 plug, LCD, 0(4)-20 mA, 2x relay,
- G94R M12 plug + 1m cable, LCD, 0(4)-20 mA, 2x relay
Transmitter for magnetic inductive sensors
Model: UMF 2
Applications
Transmitter for all Heinrichs sensors series EP and PIT
Technical data
Installation: integral or remote
Housing: Die-cast aluminum, painted
Power supply:: 115/230 VAC 50/60Hz, 10VA
24VDC, 10W
Outputs:
- Analog: 1x 0/4-20mA active, galvanically isolated
- Pulse: passive, galvanically isolated, 24V, 60mA
- Status: passive, galvanically isolated, 24V, 60mA
Ambient temperature: -20°C up to +60°C
Ingress protection: IP67
Diagnostic functions: Empty pipe monitoring, Coil current monitoring
EMC-Directive 89/336/EEC
Flow: 0,1m/s upto 10m/s
Accuracy: 0,5% of reading
Conductivity :> 5µS/cm
Communication
4-20 mA, HART® protocol
Transmitter for magnetic inductive sensors
Model: UMF3
Magnetic-Inductive flowmeter
for hazardous areas
Applications
Transmitter for magnetic inductive flow sensors series EP, EPX and PIT
Special features
- Full text indication menu structure
- 6 set buttons “Easy Operation System”
- For the use in hazardous areas
- Totalizer for flow and reflow
- Empty pipe detection, exciter current monitoring
- Remote or compact installation
Technical data
Installation: integral or remote
Power supply: 90…265VAC 50/60Hz, 19..36 VDC
Ambient temperature: -20°C up to +60°C
Ingress protection: IP68 (EN60529)
Outputs:
- Analog: 1 x 0/4-20 mA HART passive, galvanically isolated
- Pulse: passive, galvanically isolated, Um=30VDC
- Status: passive, galvanically isolated, Um=30VDC
- Diagnostic Functions: Empty pipe, exciter current
Approvals
Explosion protection
Ex II(1G) 2G Ex d e [ia Ga] IIB T6/T4/T3 Gb
Ex II(1G) 2D Ex tb IIIC [ia Ga] T80 °C / T125 °C / T 150 °C Db
Communication
4-20 mA, HART® Protocol